Where should Wii sensor bar be?

Mount the Sensor Bar to the top of the TV. The center of the Sensor Bar should be aligned with the center of the TV.

How far away should Wii sensor bar be?

The initial recommended distance for using the Wii Remote Pointer is 3 to 8 feet from the Sensor Bar. Seeing more than two dots? If you see more than two dots on the Sensitivity screen, then the Sensor Bar is picking up on additional light sources.

Is it better to have the Wii sensor bar above or below TV?

Reception may be improved by mounting the Sensor Bar to the top of the TV with the Sensor Bar Stand. Click here for more information. Important Note: If you have not already done so, be sure to set the Sensor Bar option in the Wii console's System Setting to "Below TV." This will help ensure an optimal experience .

How do I make my Wii sensor bar more accurate?

Why is my Wii sensor bar not picking up my controller?

Troubleshoot the Sensor Bar

Ensure that the Sensor Bar is plugged into the Wii U console and connected properly. If it is plugged in, unplug it and plug it back in a few times, checking after each attempt to see if the cursor shows up. You should feel it click into place when it is fully inserted.

How to Set Up Sensor Bar Position in Nintendo Wii?

How do I know if my Wii sensor bar is broken?

Adjust the camera angle and position until you can see the lights in the LCD display. If the lights are visible, the sensor bar is working. If the lights are not visible, the sensor bar will need to be replaced.

Should Wii be upright or flat?

Place the Wii console on a flat horizontal surface. The rubber feet should be facing down, the POWER Button should be on the left, and the disc slot should be on top.

How can I make my Wii look better on my TV?

Some Wii software supports a 480p progressive output that displays at an enhanced quality compared to the standard 576i display. To view Wii display output in 480p, you must change your Wii's TV Resolution setting from 50Hz (576i) or 60Hz (480i) to EDTV/HDTV (480p). Confirm your selection once it's complete.

How should Wii be placed?

The Wii console is designed with two options in mind: laying it horizontally (flat), or sitting it vertically on its side by using the included Wii Stand and Stand Plate.

Can you extend the Wii Sensor Bar?

The sensor bar extension cable connects to the end of most sensor bars and to the sensor bar port on the Wii/Wii U console. This adds a length of at least 50 feet to the sensor bar cable.

How long does Wii Sensor Bar last?

Battery Life and Performance

Like the KIMILAR, the NIFERY sensor will work with both the Wii and the Wii U. A set of fresh batteries will last for 12 hours, which is about the same as the Wiimote. If you're on the road, you'll probably want to bring an extra set or two.

How much ventilation does Wii need?

Place the console on a flat, steady surface. Place the console in an area where its intake and exhaust vents have at least 4" (10 cm) of ventilation space.

Is it OK to leave disc in Wii?

Leaving a disc inside a console that is off does absolutely no harm to either the system or the disc. I've always heard mixed feelings on this. I personally always leave the disk in and have never run in to any problem with that.

Do candles work as a Wii sensor bar?

Here's how to do it:

Place two lit candles roughly as far apart as the sensor bar is wide. In your Wii's settings, choose whether the candles are above or below the television just like you would for the sensor bar. Aim the WiiMote between the two candles and your pointer will respond on the screen like normal.

Can you use a wireless sensor bar for Wii?

The Wireless Sensor Bar allows full Wii Remote functionality without the hassle or mess of any wired connection to the console.

How do you clean a Wii sensor?

You put 2-3 drops of the supplied cleaning fluid on the pad, then insert the paddle into the Wii's disc slot. You wiggle the handle 10-20 times to clean the lens. Press the Eject button to remove the paddle, and you're done.

Why is my Wii cursor shaking?

Make sure that the Sensor Bar sensitivity is properly set: The Sensor Bar sensitivity determines the distance the player can be from the TV. If you move out of the range of the Sensor Bar the cursor can become erratic.

How do I reset my Wii sensor?

How do I get my Wii to recognize my controller?

Press and release the SYNC Button just below the batteries on the Wii Remote; the Player LED on the front of the Wii Remote will blink. While the lights are still blinking, quickly press and release the red SYNC Button on the Wii console. When the Player LED blinking stops and stays lit, the syncing is complete.

How do I fix an unresponsive Wii controller?

Install a fresh set of batteries. Clear all syncs from the Wii console. Reset the Wii remote, then sync the Wii Remote with the Wii console. Try using another Wii Remote, if possible.

Can 2 candles replace Wii sensor bar?

Just put two candles on top or lower than the television and then spread them out to about the sensor bar's length apart. Voila! Instant Wii sensor bar replacement.