Why will the Wii not read any discs?

If the disk is dirty, the Laser Lens may not properly read the disk and you may receive an error message saying Wii Unable To Read Disc or other error messages. The Laser Lens is dirty: the Laser Lens can also get dirty. If so, it will not properly scan and read the disk.

What should I do if my Wii won't read discs?

Why is my Wii U not reading Wii disc?

Remove the disc and reboot the system: Eject the problematic disc if it is still in the system. Power the system off and ensure it is placed correctly. After 30 seconds has passed, power the Wii U back on.

How do you clean the laser on a Wii?

Just remove the screws on the outer shell, carefully remove the panels until you can clearly see the disc-loader, and then apply a cotton ear swab and a dab of rubbing alcohol to the laser's lens (it'll look glassy and shiny, can't miss it).

How do you clean a laser reader?

Nintendo Wii Disk Read Error QUICK FIX

Can you replace the laser on a Wii?

Most disc read errors (DREs) can be fixed by replacing the laser lens in your Wii's DVD drive.

How do I know if my Wii sensor is broken?

Adjust the camera angle and position until you can see the lights in the LCD display. If the lights are visible, the sensor bar is working. If the lights are not visible, the sensor bar will need to be replaced.

How do I reset my Wii sensor?

How do you clean the inside of a Wii?

Use a vacuum cleaner to remove any crumbs or light objects from inside the disc tray (caddy). The vacuum should be on its lowest setting.

How to bypass Wii sensor?

To replace the sensor bar, simply light up a few candles near the TV, and bam – everything's back to normal. The reason why this works is because the Wii Remote relies on infrared lights to keep track of its position, and the candles' flames emit them.

Where is the Wii sensor?

For below the TV Screen

Insert the Sensor Bar plug into the Sensor Bar connector on the back of the Wii console. Remove the protective film from the foam pads on the bottom of the Sensor Bar.

Can you use two candles as a Wii sensor?

Just put two candles on top or lower than the television and then spread them out to about the sensor bar's length apart. Voila! Instant Wii sensor bar replacement.

Are Wiis easy to fix?

Like its competitors at the time, the Nintendo Wii is a bit more complicated to dismantle and repair than Nintendo's previous generations that could be taken apart very easily. Nevertheless this console is quite simple to disassemble and repair, even without any knowledge of electronics.

How long does a Wii last?

If you take good care of it, you can make them last 10 years easy enough. Assuming you have an average system and haven't got an unlucky combination of components.

Can a Wii be fixed?

From motherboard issues to blown fuses, our Nintendo Wii repair experts are trained to fix almost any problem—and replace it if they can't. We offer a no-cost diagnostic to figure out what's wrong with your device. The process is quick, easy, and transparent.

What can you use to clean a laser?

Hold a piece of lens tissue above the mirror and place a few drops of acetone on the paper. Lower the lens tissue onto the optic and pull it over the surface. Note that the dry part of the tissue helps remove acetone residue. Repeat the above step until the optic is clean.

Why wont my DVD player read discs?

A dirty or scratched disc surface is the most common reason for a CD/DVD issue when inserted into a computer. Check the disc for damage and confirm that the disc is compatible with your computer. Clean the disc and check for damage: Clean any dust or smudges from the disc with filtered water and a lint free cloth.

Can you clean laser lens?

Cleaning Your Laser Tube Lens: Step-By-Step Instructions

Bend your Q-tip to a 90-degree angle. This will help you reach the lens inside the laser tube. Dip one end of the Q-tip into the 100% isopropyl alcohol. Gently slide the wet end of the Q-tip into the laser tube and wipe the lens a few times in a circular motion.

How to play Wii without HDMI?

Does a Wii have a fuse?

If you have a drive which fails to spin the disc up or properly eject or "eat" discs, you may have one or two blown fuses on the drive PCB. This guide will show you how to test and replace those fuses!