Why won t my PS4 controller hard reset?

Turn over the DualShock 4 controller and locate the small hole near the left shoulder button. Unfold one end of the paper clip and insert it to push the button buried inside the hole. Hold down this button for about 5 seconds. Connect the controller to the PS4 using a USB cable.

What to do if my PS4 controller won't hard reset?

Locate the small reset button on the back of the controller near the L2 button. Use a small tool to push the button inside the tiny hole. Hold the button down for roughly 3-5 seconds. Plug in your console, connect your controller using a USB cable and press the PS button.

Why is my PS4 controller flashing white even after reset?

The PS4 controller flashing white issue is generally caused by two reasons. One is because of the low battery, and that means that you need to charge your PS4 controller to make it back on track. The other reason is that your controller is trying to connect to your PlayStation 4, but failed due to unknown factor(s).

What to do when your PS4 controller flashes blue and won t connect?

First, try resetting the controller and replacing the cable. If that doesn't fix the problem, you might need to use a different controller. If you're sure the battery or charging port on your controller is defective, you can replace it.

How do I recalibrate my PS4 controller?

Press L2 and R3 to max physical distance 3 times in a row, and rotate both joysticks with max physical distance 3 times (LED will turn off). Tap the Share button once, the LED will flash Green 3 times then turn off. This means the calibration been successfully completed.

A Warning To All PS4 Users

How do I resync my PS4 controller to my PS4?

Press and hold the PlayStation button for 3 seconds. Press and hold the 'Share' button, above the arrow buttons, and the PlayStation button at the same time. The light bar should blink now. Select your controller in the Bluetooth window of your PlayStation.

How do I reset my controller calibration?

Why are my PS4 controllers not connecting?

If your PS4 controller won't connect, try a different USB cable, in case the original one has failed. You can also reset the PS4 controller by pressing the button on the back of the controller. If your controller still won't connect to your PS4, you might need to get support from Sony.

Why is my PlayStation controller stuck blue?

This can be resolved by power cycling, resetting, then updating the console. The USB cable could be worn or damaged, as over time, wires do eventually fail. In addition, some third-party cables are unsuitable for charging the PS4 controller. Your port might be damaged, so try plugging it into another.

Why is my PS4 blinking white and not turning on?

If the indicator light only blinks white, or if the blue light never transitions to solid white, the console is frozen and needs troubleshooting. Follow the troubleshooting steps below: Unplug the console. Wait 60 seconds, plug the console back in, and turn it back on.

How do I fix the white light of death on my PS4?

Why is my PS4 controller glowing orange?

Usually, the orange light on PS4 controller means that your console is charging or in Rest Mode.

Why is my PS4 controller dead and not charging?

As we mentioned earlier, grime or a build-up of dust can cause issues when charging your PS4 controller. So, take a look at the charging port on the back of your PS4 controller. Use a wooden toothpick or some compressed air to gently clean the port and test the controller again to see if it charges now.

Why did my PS4 controller suddenly stopped working?

Common reasons your PS4 controller is not working

The controller's battery is dead. The controller was recently paired with another device, like a different PS4 or PC. The controller is too far from your PlayStation and is no longer connected via Bluetooth®.

What does a hard reset do on a controller?

A hard reset is when a device is reverted back to its factory default settings, which is basically how it came out of the box. If a soft reset fails and you're still having troubles, this process can frequently resolve any problems.

What does factory reset do in controller?

To decommission or reset your access controller to factory settings, you'll need to decommission it from Command. This will also delete all user-related data from the controller and allow it to be transferred to a new organization.

How do I know if my PS4 controller is pairing?

While pressing and holding the SHARE button, press and hold the PS Button until the light bar flashes. Enable Bluetooth on your device, and then select the controller from the list of Bluetooth devices. When pairing is complete, the light bar blinks, and then the player indicator lights up.

What do colors on PS4 controller mean?

The color that is assigned depends on the order in which each user presses the PS button. The first controller to connect is blue, the second is red, the third is green, and the fourth is pink.

What is the yellow light of death PS4?

PS4 Controller Light Yellow refers standby mode. This happens because the system might be charging or the controller is not connected to the console.